幸运28计划软件app

John Broskie's Guide to Tube Circuit Analysis & Design

幸运28计划软件app26 september 2018                                                                     post 440

 

Balanced Systems
幸运28计划软件app Based on recent email that I have received, balanced audio surges in popularity. If it has, why has it? Perhaps because so many standalone DACs sport balanced XLR output jacks, many audiophiles decided to give them a listen and liked what they heard. And there is much to like about balanced audio systems. Indeed, I wish that a century ago they had established balanced input and output as the standard for all audio devices. Now, get ready for the BIG HOWEVER. The key feature to a balanced system, however, is common-mode signal rejection, wherein signals shared between the two phases that are equal in magnitude and in-phase are ignored and only differential signals get amplified and are allowed pass through to the output.

we live in an amazingly noisy electrical world. the sun spits out radio frequency interference, as does lightning. computer power supplies, light dimmers, car ignition systems, vacuum cleaners, industrial equipment, neon signs, cell phones, and a few hundred thousand other electrical devices all add to electrical circuitry being dirtied by electromagnetic induction and electrostatic coupling. in my house alone, over 20 wifi and bluetooth enabled devices are found.

balanced audio sidesteps much of this electrical pollution due to its common-mode signal rejection, whereby a signal common to both phases, such as extraneous electrical noise, gets rejected. on the other hand, a balanced system that fails to provide common-mode signal rejection is not delivering the true potential of a true balanced system. for example, the following circuit accepts a balanced pair of input signals, and it puts out two output signal in opposite phase, but does not deliver any common-mode signal rejection.

if the same input signal is presented to both grids, both triodes will amplify the shared signal. in contrast, the following balanced circuit will largely reject the common-mode signal.

the constant-current source and the bridging of the two cathodes made all the difference. a common-mode signal becomes invisible to the two grids, as the bridged cathodes simply follow the common-mode signal and the triodes maintain a constant-current draw, so no change in plate voltage occurs, so in turn no output signal is developed.

by adding an input 1:1 transformer to the defective balanced circuit, however, the circuit is transformed in to a fully balanced circuit, as the input transformer's intrinsic common-mode signal rejection saves the day.

幸运28计划软件appthe problem with input signal transformers is their high cost and limited frequency bandwidth. while the high cost is truly regrettable to most, it could be viewed as feature hardcore audiophiles; moreover, the truncated frequency bandwidth can actually prove a feature, as subsonic and ultrasonic signals can cause audio-system headaches. for example, warped lps and rfi only subtract from the musical content. moreover, a good input transformer can solve problems, such as ground loops and house-ground loops, better than any other approach.

i must admit that i used to be profoundly anti signal transformer, but i have made a complete reevaluation of their merits and disadvantages. i now firmly believe that a good signal transformer can be a blessing. my first experiences with signal transformers were poor due to my experimenting with poor signal transformers that i had pulled from old clunker electronic gear. these were cheaply made transformers with dismal core material and no shielding. in contrast, the fine signal transformers made by altec, cinemag, jensen, lundahl, tango, and others. although expensive, deliver excellent performance.

one potential problem we face with signal and tube-based gear is the relatively high impedances and resistances in tube circuits. unlike capacitors, which thrive in high-impedances applications, transformers work best with low impedances. the 600-ohm termination standard in professional audio was imposed to allow signal to work better. ideally, a tenfold or hundredfold decrease in impedance would make it far easier to use signal transformers. think about it: in a large auditorium, filled with a thousand lights, lights that do no simply turn on and off, but are slowly brought to life with power dimmers; and filled motorized curtains and miles of electric cabling, the lower the termination impedance, the less electrical interference can seep into the desired signal.

with solid-state gear, low impedances are easy to realize, but not so with tube gear. for example, a 12ax7-based cathode follower will struggle to drive a 10k potentiometer. in other words, we need to ensure that our tube-based gear is up to the task of driving the signal transformer.

幸运28计划软件appmany will argue that we needn't brother, as balanced, low-impedance-terminated gear only makes sense in a professional-audio application, not in a home. i used to believe this as well. i no longer do, as our homes are no longer as electrically-noise-free as they once were. here is an example that i am sure i have mentioned before: i was at a buddy's house, listening to his excellent stereo system, when i heard a buzzing sound sully the sonic glory. i had heard a similar buzz before and i asked him if his wife was home. she was. i then asked to see if she had turned on a light dimmer partially. she had. he turned it off and the buzz was gone. a month later, we are listening away again and the same buzz entered the sound. his wife wasn't home. he looked out his window and pointed to the house next door, explaining to me that his neighbors light dimmers also pollute his system. i assume that they both shared the same power company transformer on the telephone pole. perhaps some fancy line conditioner would have solved the problem, but i bet a completely balanced system could have sidestepped the buzz.

 


Balanced Phono Preamps
幸运28计划软件app I have been thinking about balanced phono stages for weeks now. I like the idea of the cartridge's delicate signal being amplified in a balanced fashion. One thought I have had is that the best path might be to use OpAmps to amplify the small signal enough to pass the signal on to a tube-based line-stage amplifier and power amplifier. A friend bought one of those USB turntables that hold a phono preamp and ADC internally. Sure it's not high-end, but it is surely easy. Well, what if we built a small OpAmp-based balanced phono stage that rest under our fancy turntable?

幸运28计划软件appone design that came to mind was the following, which uses two stages.

the two input opamps provide all the gain and establish the 50hz to 550hz riaa equalization. the problem with this topology is that its common-mode-rejection ratio (cmrr) is equal to its gain. still, this is a huge improvement over the following variation, which offers no cmrr.

幸运28计划软件appnote how two resistors are used and how their nexus goes to ground. in contrast, the single-resistor version puts out the common-mode signals at unity gain.

幸运28计划软件appthey way we achieve a higher ccmr is with the second stage, which consist of two differential unity-gain amplifiers.

幸运28计划软件appas long as tightly matched resistors are used throughout, we can achieve a high cmmr. in addition, these differential amplifiers set the 2122hz riaa equalization by encompassing a low-pass filter on the balanced input signals. if we want an unbalanced output signal, we can simply use a single opamp in the second stage.

okay, let's now move on to a hybrid balanced phono stage. the design uses the input stage from the previous solid-state design and uses a passive rc filter to realize the 2122hz (75µs) riaa equalization.

幸运28计划软件appthe constant-current source that loads the the two joined cathodes grants the triode-based differential amplifier its stellar cmrr. in other words, the opamp portion only gets partially there, while the differential tube stage furthers the cmrr.

The "Aikido" aspect of this circuit is found in the last stage, which undoes the first tube differential's extremely poor PSRR, i.e. next to none. See post 431 for more details on the Aikido differential amplifier. By the way, Note that no negative power-supply rail was used in the circuit shown above. This might prove a problem with the solid-state constant-current source, as it might become voltage starved. If you are using a step-up transformer, the following workaround gives the grids a small positive voltage to increase the cathode voltage, giving the constant-current source more voltage to work within.

By the way, be sure check out post 327幸运28计划软件app for this interesting variation that does not use a constant-current source.

no step transformer is used in this example—but it could be. adding an input transformer will add common-mode signal rejection.

 

 

Going Horizontal
My last post strove to force a super-triode overlay on the the SRPP, White cathode follower, and SRCFPP output stages. Well, I will now continue the horizontal movement, starting with the White cathode follower.


The first thing to note is the low voltage drop across the constant-current sources. In other words, not much heat will dissipated by the constant-current sources. So, if removed them and doubled the B+ voltage and placed the circuit in a vertical arrangement, the decrease in wasted heat will prove modest. On the other hand, by going horizontal, we gain two huge advantages: the transistors will not go into a current runaway mode and the big-valued output capacitors can be low in voltage value, which allows us to use the much better sounding non-polarized electrolytic capacitors.

幸运28计划软件apphow well does this circuit work? extremely well, in terms of thd. here is the spice-generated fourier graph.

this represents less than 0.1% thd. the one problem with this circuit, much like the standard white cathode follower, is relatively poor psrr. we can overcome this failing by making an aikido push-pull amplifier.

幸运28计划软件appnote the 2.2µf capacitor and the two-resistor voltage divider that feeds the rightmost triode's grid. the input stage leaks 50% of the power-supply noise at its output, so we feed a portion of this noise slightly greater than 50% to the rightmost triode's grid, which will force a ripple null at the output.

here is its fourier graph.

幸运28计划软件appthe 2nd and 3rd harmonics are lower with the input stage in place, but all the other harmonics are higher. interesting. do not forget that this circuit is not just a buffer, but a gain stage.

幸运28计划软件appnow, it's time to go horizontal with the srcfpp.

once again, the constant-current sources allow the horizontal move and save the day. transistors are tweaky devices due to their screaming transconductance, as an extra 0.1v on the transistor gate makes for a huge increase in current conduction, which is why emitter resistors are so often used. in this circuit, the mur410g rectifiers offer very little effective series resistance, so they cannot save the day. the constant-current sources, on the other hand, set strict idle current limit.

the thd is wonderful, coming in at below 0.01%.

the output impedance was less than 10ohm in spice simulations and the psrr was at least -40db, if not closer to -60db.

all of these circuits belong to the trinity of lazy push-pull circuits. and all made use of 100ma constant-current sources, which implies a peak output current swing of 200ma, which into a 32-ohm load implies a peak voltage swing of 6.4vpk, a peak voltage we are not likely to actually realize, as the constant-current sources only allow for about a 3vpk swing before they are voltage starved. speaking of the constant-current sources, the simplest way to implement would be to use an lm317-hv, which is good for up to 57v of voltage differential.

幸运28计划软件appthe 12.4-ohm resistor sets an idle current flow of 100ma. if a plain lm317 is used, we should place a 30v zener in parallel with the constant-current sources.

 

 

 

Music Recommendation:Duets by Kevin Eubanks, Stanley Jordan
Here is how I often discover new music: I do a search in Tidal for all the covers of the classic song, for example, Summertime, by George Gershwin. After a few hundred tracks show up, I press play. Invariably one artist will just delight me and I I have to hear from them. For example, I just loved Sam Cooke's cover of Summertime幸运28计划软件app and I quite enjoyed Renee Olstead and Angélique Kidjo's covers. When doing this these searches, I often find I end up liking singers that I think that I don't like, such as Mel Tormé—dang, he could sing.

Well, when I heard Kevin Eubanks and Stanley Jordan guitar duet of Summertime, I had to hear the rest their Album, Duets. Not only is the music intensely satisfying, the recording is exemplary. Highly recommended. With Tidal, you must search for "Kevin Eubanks," not "Stanley Jordan," as Tidal does not list this album in Jordan's list of albums.

//jrb

 

 

 

 

 

幸运28计划软件app    

User Guides for GlassWare Software
幸运28计划软件app Just click on any of the above images to download a PDF of the user guides. By the way, all the links for the PCB user guides shown at the right now work.

 

幸运28计划软件appfor those of you who still have old computers running windows xp (32-bit) or any other windows 32-bit os, i have setup the download availability of my old old standards: , , and . the downloads are at the glassware-yahoo store and the price is only $9.95 for each program.

so many have asked that i had to do it.

幸运28计划软件appwarning: these three programs will not run under vista 64-bit or windows 7 & 8 or any other 64-bit os.

幸运28计划软件appi do plan on remaking all of these programs into 64-bit versions, but it will be a huge ordeal, as programming requires vast chunks of noise-free time, something very rare with children running about. ideally, i would love to come out with versions that run on ipads and android-os tablets.

 

//jrb

 

   

 

 

 

john gives

Special Thanks to the Special 66


幸运28计划软件app To all my patrons, all 66 of them, thank you all again. I want to especially thank

Concordio Anacleto

Andrew Rintoul

Jason Stoddard

Kelvin Tyler

幸运28计划软件appi am truly stunned and appreciative of their support.

幸运28计划软件appin addition i want to thank

John Atwood

Hal Clark

Eduardo Fayad

Mike Galusha

Erik Hoel

Neil Kovacs

Paul Reid

Marty Reiss

Paulo Mario dos Santos Dias de Moraes

James Tiemann

all of your support makes a big difference. i would love to arrive at the point where creating my posts was my top priority of the day, not something that i have to steal time from other obligations to do. the more support i get, the higher up these posts move up in deserving attention.

幸运28计划软件apponly those who have produced a technical white paper or written an article on electronics know just how much time and effort is required to produce one of my posts, as novel circuits must be created, spice simulations must be run, schematics must be drawn, and thousands of words must be written.

if you have been reading my posts, you know that my lifetime goal is reaching post 1,000. i have 560 more to go.

幸运28计划软件appmy second goal is to gather 1,000 patrons. i have 934 patrons to go. help me get there.

 


Only $12.95
to keep track of your
tube and part collection

TCJ My-Stock DB

TCJ My-Stock DB helps you know just what you have, what it looks like, where it is, what it will be used for, and what it's worth. TCJ My-Stock DB helps you to keep track of your heap of electronic parts. More details.

Version 2 Improvements
  
List all of your parts in one DB.
    Add part Images.
    One-click web searches for part information.
    Vertical and horizontal grids.*
    Create reports as PDFs.*
    Graphs added 2D/3D: pie & bar.*
    More powerful DB search.
    Help system added.
    Editable drop-down lists for location, projects,         brands, styles, vendors and more.

幸运28计划软件app     *user definable

Download for
XP to Win 10

For more information, please visit:

           www.glass-ware.com
 
cdvem.com           Copyright © 1999-2018 GlassWare           All Rights Reserved
幸运28计划app苹果版 分分快3计划预测软件 大发一分钟快3全天计划 一分快3和值大小稳赚公式 分分快三最准全天计划